products
产品分类article
相关文章简要描述:美国Holaday HI 3804 RF工频磁场测试仪主要功能特点介绍:HI-3804工业电磁场测试仪的各向同性探针能够测量感应电场和磁场。
美国Holaday HI 3804 RF工频磁场测试仪
主要功能特点介绍:
HI-3804工业电磁场测试仪的各向同性探针能够测量感应电场和磁场。
主要特点:
数据资料记录(112点)
电和磁场力量测量
场强长条图
便宜的EMF侦查
在机上数据资料记录和回顾
在范围(超载)警告警报
Planewave等效功率密度读出选择
美国Holaday HI 3804 RF工频磁场测试仪特点描述:
HI-3804是一种便宜的EMF侦查和测量解答为应用在10 - 42兆赫主义频带。设备在高领域环境里简化要求的测试方法确定电磁场放射服从例如RF热化和焊接。特点包括在机上数据资料记录和回顾、电和磁场力量测量、线性和功率密度部件显示和.05 - 50 mW/cm2的一个力学范围。
标准配置:
便携包
用户手册
电子规格
物理规格
仪器规格:
电池:9 V碱性电池(2)
显示单位:V/m, A/m, mWcm2
环境: 0 - 95%湿度,不能结露、10 - 40°C。
2数显推拉力计
模式 | 标准型 | FGC-0.2 | FGC-0.5 | FGC-1 | FGC-2 | FGC-5 |
经济型 | — | — | — | FGN-2 | FGN-5 | |
定额负荷量 | ±1.961N | ±4.903N | ±9.81N | ±19.61N | ±49.03N | |
±200.0gf | ±500.0gf | ±1000gf | ±2.000kgf | ±5.000kgf | ||
±8.00ozf | ±16.00ozf | ±2.000lbf | ±5.000lbf | ±10.00lbf | ||
测量范围 | ±2.00N | ±5.000N | ±10.00N | ±20.00N | ±50.00N | |
±200.0gf | ±500.0gf | ±1000gf | ±2.000kgf | ±5.000kgf | ||
±8.00ozf | ±16.00ozf | ±2.00lbf | ±5.00lbf | ±10.00lbf | ||
分辨率 | 0.001N/0.1gf/0.01ozf | 0.01N/1gf/0.001lbf | 0.1N/0.001kgf/0.01lbf | |||
测量单位 | (易于转换显示功能单位) | |||||
测量方法 | 正常测定和峰值测定 | |||||
更新时间 | 0.3秒 | |||||
测量次数 | 35次/秒 | |||||
精度 | ±0.2%R.C.+1/2位(23C) | |||||
温度效应 | 变化范围:零点偏移/因牵引而消除 | |||||
显示 | 4位12mm高LCD,1个张力显示用(可选转换显示)其他显示器:1.“LOWBAT" 2.“BAT"(电池正充电)3.“OVR"(超载)4.“PEAK"(峰值模式) | |||||
超载容许 | R.C. 200% | |||||
Teacking功能 | 开/关可供选择 | |||||
输出信号 | RS-232C | 有(通过通信软件,可以与PC连接.与PC的连接线为另卖品)连续送信zui大为100次/秒 | ||||
模拟 | ±1V(±zui大值载入)12位D/A转换方法,输出间隔140次/秒 | |||||
超载 | 开放式连接器输出(DC30V 5mA zui大值) | |||||
电源 | 镍镉电池和AC适配器(DC9V 200mA) | |||||
电源自动关闭功能 | 待机10分钟,由AC供电时能够连续使用 | |||||
操作温度 | 0~40℃ | |||||
尺寸 | 宽75*高38*长147mm | |||||
重量 | 约450g | |||||
附件(包括在内) | 扁平顶盖,挂钩,钢凿,三角带,椎体,扩展杆,便携式提箱,直流电源适配器,RS-232C线 |
FGC-100HB测力仪模式
标准型
FGC-0.2
FGC-0.5
FGC-1B
FGC-2B
FGC-5B
经济型
—
—
—
FGN-2B
FGN-5B
定额负荷量
±1.961N
±4.903N
±9.81N
±19.61N
±49.03N
±200.0gf
±500.0gf
±1000gf
±2.000kgf
±5.000kgf
±8.00ozf
±16.00ozf
±2.000lbf
±5.000lbf
±10.00lbf
测量范围
±2.00N
±5.000N
±10.00N
±20.00N
±50.00N
±200.0gf
±500.0gf
±1000gf
±2.000kgf
±5.000kgf
±8.00ozf
±16.00ozf
±2.00lbf
±5.00lbf
±10.00lbf
分辨率
0.001N/0.1gf/0.01ozf
0.01N/1gf/0.001lbf
0.1N/0.001kgf/0.01lbf
测量单位
(易于转换显示功能单位)
测量方法
正常测定和峰值测定
更新时间
0.3秒
测量次数
35次/秒
精度
±0.2%R.C.+1/2位(23C)
温度效应
变化范围:零点偏移/因牵引而消除
显示
4位12mm高LCD,1个张力显示用(可选转换显示)其他显示器:1.“LOWBAT" 2.“BAT"(电池正充电)3.“OVR"(超载)4.“PEAK"(峰值模式)
超载容许
R.C. 200%
Teacking功能
开/关可供选择
输出信号
RS-232C
有(通过通信软件,可以与PC连接.与PC的连接线为另卖品)连续送信zui大为100次/秒
模拟
±1V(±zui大值载入)12位D/A转换方法,输出间隔140次/秒
超载
开放式连接器输出(DC30V 5mA zui大值)
电源
镍镉电池和AC适配器(DC9V 200mA)
电源自动关闭功能
待机10分钟,由AC供电时能够连续使用
操作温度
0~40℃
尺寸
宽75*高38*长147mm
重量
约450g
附件(包括在内)
扁平顶盖,挂钩,钢凿,三角带,椎体,扩展杆,便携式提箱,直流电源适配器,RS-232C线
55075010数显扭矩扳手
左右手适用,精细棘轮头。Nm,ft.ib和In.Ib三刻度显示,LED指示灯指示功能。两种工作模式。 电脑及打印机连口。+/-2%高精确度,有独立的检验证书和序列号。
ACX-500数字航天电缆张力计
ACX-100数字航空用钢丝绳张力计
STANDARD INSTRUMENTS: |
Model | Range | Resolution | Standard Cable Selections |
ACX-100 | 5-100 lbs | 0.5 lb | 1/16", 3/32", 1/8", 5/32" |
ACX-250 | 20-250 lbs | 0.5 lb | 1/16", 3/32", 1/8", 5/32" |
ACX-500 | 40-500 lbs | 1 lb | 3/32", 1/8", 5/32" |
ACX-CWT | 20-250 lbs | 0.5 lb | CWT-5,CWT-10,CWT-15,CWT-20,CWT-25 |
ACX-CMB | 20-250 lbs | 0.5 lb | 1/16",3/32",1/8",5/32", CWT-5 thru CWT-25 |
*Calibrations for 3/16", 7/32" and for metric sized cables can be added to the cable selection menu upon request, however cables with diameters larger than 5/32" will only indicate up to approximay 90% of maximum tension range. For example, an instrument scaled for a maximum tension range of 250 lbs will display readings up to approximay 225 lbs on 7/32" or 3/16" diameter cables.
· Available Options for all Instruments |
Option designator -A | Analog Output Option |
Option designator -E | RS-232 Serial Output Option |
Option designator -D | Data Logging Option Option |
Note: Add option-designator letter to the end of the Model Number. (For example, a Model ACX-250-E denotes a standard ACX-250 with the optional RS-232, serial output function included.)
· Instruments can be configured with any or all of these options.
ACX-100数字航空用钢丝绳张力计
STANDARD INSTRUMENTS: |
Model | Range | Resolution | Standard Cable Selections |
ACX-100 | 5-100 lbs | 0.5 lb | 1/16", 3/32", 1/8", 5/32" |
ACX-250 | 20-250 lbs | 0.5 lb | 1/16", 3/32", 1/8", 5/32" |
ACX-500 | 40-500 lbs | 1 lb | 3/32", 1/8", 5/32" |
ACX-CWT | 20-250 lbs | 0.5 lb | CWT-5,CWT-10,CWT-15,CWT-20,CWT-25 |
ACX-CMB | 20-250 lbs | 0.5 lb | 1/16",3/32",1/8",5/32", CWT-5 thru CWT-25 |
*Calibrations for 3/16", 7/32" and for metric sized cables can be added to the cable selection menu upon request, however cables with diameters larger than 5/32" will only indicate up to approximay 90% of maximum tension range. For example, an instrument scaled for a maximum tension range of 250 lbs will display readings up to approximay 225 lbs on 7/32" or 3/16" diameter cables.
· Available Options for all Instruments |
Option designator -A | Analog Output Option |
Option designator -E | RS-232 Serial Output Option |
Option designator -D | Data Logging Option Option |
Note: Add option-designator letter to the end of the Model Number. (For example, a Model ACX-250-E denotes a standard ACX-250 with the optional RS-232, serial output function included.)
· Instruments can be configured with any or all of these options.
STX-2000张力计
STANDARD INSTRUMENTS: STX-Series Models are calibrated specifically to your strapping types(s) and size(s) to ensure greatest accuracy. |
Model | Range | Resolution | Full-Scale Accuracy |
STX-2000 | 100-2000 lbs | 10 lb | 2% |
STXM INSTRUMENTS: STXM instruments include multiple calibrations for different Poly and PET strapping sizes. |
Model | Range | Resolution | Full-Scale Accuracy |
STXM-2000* | 100-2000 lbs | 10 lb | 4% |
STX-1000张力计
STANDARD INSTRUMENTS: STX-Series Models are calibrated specifically to your strapping types(s) and size(s) to ensure greatest accuracy. |
Model | Range | Resolution | Full-Scale Accuracy |
STX-1000 | 50-1000 lbs | 5 lb | 1% |
STXM INSTRUMENTS: STXM instruments include multiple calibrations for different Poly and PET strapping sizes. |
Model | Range | Resolution | Full-Scale Accuracy |
STXM-1000 | 50-1000 lbs | 5 lb | 4% |
*The STXM-2000 includes all calibrations for POLY and PET strapping with thicknesses from .020" - .055", and STEEL strapping with thicknesses between .017" - .044".
· Data Logging has adjustable duration and sampling rates.
· Large, easy to read backlit, graphic display with adjustable backlighting and contrast.
· Select tension values to display in lbs, Kg, or Newtons.
· Select strap material and size from menu. Instrument automatically adjusts calibration for your specific setting.
· Up to 10 calibrations can be programmed into instrument. (All calibrations password protected.)
· Adjustable LCD refresh rates allow for stable digital readings.
· All models typically available from stock.
· All models factory-calibrated and ready for use.
· Calibration values traceable to National Standards. Calibration certificate included.
Available Options for all Instruments |
· Note: Add option-designator letter to the end of the Model Number. (For example, a Model STX-1000-A denotes a standard STX-1000 with the optional Analog Output function included.)
A | Analog Output Option |
E | RS-232 Serial Output Option |
D | Data Logging Option |
ACM-600张力计
CX-2000张力计
CX-2000张力计
TR-25机械张力计
Model "TR" Series |
Range In Grams | Use Model Number |
25 g | TR-25 |
125 g | TR-125 |
250 g | TR-250 |
1000 g | TR-1000 |
2000 g | TR-2000 |
4000 g | TR-4000 |
5000 g | TR-5000 |
WC系列张力计
The Sheet Tension Meter, Model WC-series, measures the tension of any width material which is long, flat and thin, such as: paper, film, plastic sheets, cloth, web, loom beams, metal foils or winding electrical condensers.
The Sheet Tension Meter, Model WC-series measures tension in flexible sheets or webs which are typically 8" or wider. The instrument is inserted from the edge and measures per inch of web width up to 4" inside your material, so the waviness at the edges is avoided. Hand crafted from solid anodized aluminum, ranges are available to measure tension up to 100 pli or 50 kg/pli.
Ensure consistency in your manufacturing process.
Direct Reading or Comparator Dials Available.
Adaptable for materials as thin as paper to sheets as stiff as foils.
Engagement and disengagement onto materials is quick, safe and easy.
Readings are obtained regardless of meter position.
Weighs only 3 lb. LX-250张力计
For use on materials with critical tension ranges up to 500 lbs.
Large, easy to read, graphic display with adjustable backlighting and contrast.
Select tension values to indicate in Lbs, Kg or Newtons.
Display shows Tension, Battery Charge level and Material selected.
Push a button to activate the Memory Function to store and display up to five separate tension readings plus the average value (AVG) of these stored readings.
Accuracy is +/- 2% full-scale for all menu-selectable calibrations. Accuracy for custom calibrations is material specific. • Up to 10 calibrations can be programmed into instrument. (All calibrations are password protected to provide due diligence against unauthorized changes).
Adjustable LCD refresh rates allow for stable digital readings.
All models typically available from stock.
All models factory calibrated and ready for use.
All calibration values traceable to National Standards.
Calibration certificate included.
MODEL | RANGE | RESOLUTION |
LX-250 | 5-250 LB Grooved Pulleys | 0.5 LB |
AVAILABLE OPTIONS FOR ALL INSTRUMENTS
Note: Add option designator to the end of the part number. (i.e.: a Model LX-250-E denotes a standard, LX-250 with the optional RS-232, serial output function installed).
-A Analog Output option. 0-5 VDC or 4-20mA with Software-definable ending sequences. Provided with 10’ of cable. Data outputted at 40 Hz.
-E RS-233 Serial Output option. Provided with 10’ cable to Interface with your receiving device. Select data sampling rate from 1, 2 or 5 Hz.
Input Real-Time Serial Data into any Windows® application using the optional software WinWedge Pro® for Windows, or configure your Window’s® operating system to capture the data via Hyper Terminal®.
SPECIFICATIONS:
Approximate weight is 1-1/2 lb (Weight varies depending upon instrument configuration).
Re-chargeable NIMH battery with power supply provided. Recommended temperature range for instruments is 35 - 115° F. Approximay 6 hours of operation per battery charge depending upon backlighting intensity.
Power Supply operates with input voltages from 100 – 240V and includes several, interchangeable “blades" allowing use with European, US, Australian and other plug configurations.
Automatic shutoff after 10 minutes of non-use.
Instruments may be operated continuously while connected to power supply.
Durable, lightweight carrying case with protective foam inserts.
CE Certification complying with heavy, industrial immunity standards.
BTM系列张力计pical Weight: 2 lb, 14 oz
Easy To Read Dial in lg or kg
Right- or Left-Hand Operation
Durable Solid Anodized Aluminum Construction
Sturdy Handle For Ease of Use on Moving Materials
Provided with Heavy Duty Polyethylene Carrying Case
Stainless Steel, Anodized Aluminum, P.T.F.E. or Delrin Contact Elements Available
The Band Tension Meter is used to measure the tension in tapes or many wires/yarns in parallel. Ranges are available up to 500 lb or 250 kg. This instrument is ideal for use with bands, flat cable, and flat conductors as well as round wire/cable configurations. The contact rollers can be made up to 3" long, plus the instrument can be outfitted with a variety of small grooved pulleys for round wire and cable applications. Please Tensitron if you would like assistance in selecting the appropriate meter for your specific application.
LXR-500张力计For use on materials with critical tension ranges up to 500 lbs.
Large, easy to read, graphic display with adjustable backlighting and contrast.
Select tension values to indicate in Lbs, Kg or Newtons.
Display shows Tension, Battery Charge level and Material selected.
Push a button to activate the Memory Function to store and display up to five separate tension readings plus the average value (AVG) of these stored readings.
Accuracy is +/- 2% full-scale for all menu-selectable calibrations. Accuracy for custom calibrations is material specific. • Up to 10 calibrations can be programmed into instrument. (All calibrations are password protected to provide due diligence against unauthorized changes).
Adjustable LCD refresh rates allow for stable digital readings.
All models typically available from stock.
All models factory calibrated and ready for use.
All calibration values traceable to National Standards.
Calibration certificate included.
MODEL | RANGE | RESOLUTION |
LXR-500 | 25-500 LB 1" Tape Roller | 1 LB |
AVAILABLE OPTIONS FOR ALL INSTRUMENTS
Note: Add option designator to the end of the part number. (i.e.: a Model LX-250-E denotes a standard, LX-250 with the optional RS-232, serial output function installed).
-A Analog Output option. 0-5 VDC or 4-20mA with Software-definable ending sequences. Provided with 10’ of cable. Data outputted at 40 Hz.
-E RS-233 Serial Output option. Provided with 10’ cable to Interface with your receiving device. Select data sampling rate from 1, 2 or 5 Hz.
Input Real-Time Serial Data into any Windows® application using the optional software WinWedge Pro® for Windows, or configure your Window’s® operating system to capture the data via Hyper Terminal®.
SPECIFICATIONS:
Approximate weight is 1-1/2 lb (Weight varies depending upon instrument configuration).
Re-chargeable NIMH battery with power supply provided. Recommended temperature range for instruments is 35 - 115° F. Approximay 6 hours of operation per battery charge depending upon backlighting intensity.
Power Supply operates with input voltages from 100 – 240V and includes several, interchangeable “blades" allowing use with European, US, Australian and other plug configurations.
Automatic shutoff after 10 minutes of non-use.
Instruments may be operated continuously while connected to power supply.
Durable, lightweight carrying case with protective foam inserts.
CE Certification complying with heavy, industrial immunity standards.
ATLAS系列高载荷测试机ATLAS系列高载荷测试机ATLAS5到50KN测试机用于测试力大于5KN的试验中。强力发动机和双柱结构的结合使该机与STENTORS有相似的功能。基座有一个适于安装夹具的固定孔。传感器固定于横梁上,横梁由双螺杆系统移动,并由双立柱导轨控制升降。ATLAS系列的控制台和STENOR采用相同的控制系统。
ANDILOG传感器
型号 | 精度 | 量程 | 分辨率 |
SPIP TM 0.4 | 0.5%FS | 0.4Nm | 0.05mNm |
SPIP TM 0.7 | 0.5%FS | 0.7Nm | 0.07mNm |
型号 | 精度 | 量程 | 分辨率 |
SPIP TH 0.12 | 0.5%FS | 0.12Nm | 0.01mNm |
SPIP TH 0.3 | 0.5%FS | 0.3Nm | 0.03mNm |
SPIP TH 1.5 | 0.5%FS | 1.5Nm | 0.1mNm |
SPIP TH 0 | 0.5%FS | 6Nm | 0.6mNm |
SPIP TH 12 | 0.5%FS | 12Nm | 1mNm |
型号 | 精度 | 量程 | 分辨率 |
SPIP TT 0.05 | 0.5%FS | 0.05Nm | 0.005mNm |
SPIP TT 0.15 | 0.5%FS | 0.15Nm | 0.02mNm |
SPIP TT 0.35 | 0.5%FS | 0.35Nm | 0.03mNm |
SPIP TT 0.75 | 0.5%FS | 0.75Nm | 0.1mNm |
SPIP TT 1 | 0.5%FS | 1Nm | 0.1mNm |
SPIP TT 3 | 0.5%FS | 3Nm | 0.3mNm |
SPIP TT 6 | 0.5%FS | 6Nm | 0.6mNm |
SPIP TT 12 | 0.5%FS | 12Nm | 1mNm |
SPIP TT 24 | 0.5%FS | 24Nm | 2mNm |
SPIP TT 60 | 0.5%FS | 60Nm | 5mNm |
型号 | 精度 | 量程 | 分辨率 |
SPIP TW 15 | 0.5%FS | 15Nm | 1mNm |
SPIP TW 60 | 0.5%FS | 60Nm | 6mNm |
SPIP TW 150 | 0.5%FS | 150Nm | 0.02mNm |
SPIP TW 600 | 0.5%FS | 600Nm | 0.06mNm |
EASY带TM传感器数显扭力计同样使用了CENTOR技术。CENTOR W EASY数显扭力计采用一个超大的显示屏可以显示精确测量结果。它可以同时显示当前值、峰值。进度条显示了测量是否接近zui大量程。如有需要背景光可以让读数更加容易。
它*的测量设备可以使取样频率在1000赫兹,分辨率在1/10000FS,误差小于0.5%(满量程)。
同时还可拓展其它多种功能来完善该仪器。
设点功能可以设置“合格,不合格",同时信号会在显示屏上表示出来,通过RS232输出端可以连接电脑。
数字输出可以用Mitutoyo打印机进行数据打印。
技术参数
·顺、逆时针双向转动
·精度:0.5%(满量程)
·分辨率:1/1000FS
·峰值锁定功能(双向)
·当前值和峰值同时显示
·进度条显示功能
·三种单位:牛米、千克厘米、毫牛米
·取样频率:1000赫兹
·可以用脚踏开关
·校准功能
·.5-15分钟自动关机(可调)-
·可编程设置功能
·.双口RS232输出:随意传输zui大、zui小或当前值
·数字输出
·连续工作8小时不用充电
·快速充电
·翻转显示功能
·背景光显示
·可充电电池
·低电提示
·配置记忆功能
·金属外壳并且内部有弹性保护膜
·背后有用于固定在支架上的螺孔
·校准证书
·.装有适配器和附件的便携工具箱
型号 | 量程 | 分辨率 |
CNR EA TM-04 | 0.4Nm | 0.04mNm |
CNR EA TM-07 | 0.7Nm | 0.07mNm |
Star带TW传感器数显扭力计技术参数:
◆ 顺、逆时针测试
◆ 精度:0.5%
◆ 分辨率:1/10000FS
◆ 双向峰值保持
◆ 当前值和峰值同时显示
◆ 扭矩/时间曲线图
◆ 显示曲线图上的特殊点:zui大值、任一时间值、拐点、导数值、*峰值、开始和结束值、平均值等
◆ 上一曲线图的保存
◆ 进度条显示
◆ 三个单位:Nm,Kg.cm,cm,mNm
◆ 取样频率:1000赫兹
◆ 可以用脚踏开关
◆ 校准功能
◆ 5~15分钟自动关机(可调)
◆ 可编程设置功能
◆ 双口RS232输出:随意传输zui大、zui小或当前值
◆ 数字量输出
◆ 曲线图输出
◆ 每秒50个值的传输速度
◆ 当前值的设定保护功能
◆ 自动确认传感器
◆ 可翻转显示功能
◆ 连续工作8小时不用充电
◆ 快速充电
◆ 可逆测量
◆ 背景光显示
◆ 可充电电池
◆ 低电提示
◆ 配置记忆功能
◆ 金属外壳并且内部有弹性保护膜
◆ 背后有用于固定在支架上的螺孔
◆ 校准证书
◆ 装有适配器和附件的便携工具箱
型号 | 量程 | 分辨率 |
CNR ST TW-15 | 15Nm | 1.5mNm |
CNR ST TW-60 | 60Nm | 6mNm |
CNR ST TW-150 | 150Nm | 0.015mNm |
CNR ST TW-600 | 600Nm | 0.06mNm |
UTCM 20L00050机械扭力计5.提供标准金属仪表箱
机型 | 量程(Force) | 分辨率(Force) | 产品说明 |
UT CM 20L00002 | 2 - 20 Ncm | 2 Ncm | MECH TORQUE GAUGE |
UT CM 20L00004 | 5 - 40 Ncm | 5 Ncm | MECH TORQUE GAUGE |
UT CM 20L00008 | 10 - 80 Ncm | 10 Ncm | MECH TORQUE GAUGE |
UT CM 20L00016 | 20 - 160 Ncm | 20 Ncm | MECH TORQUE GAUGE |
UT CM 20L00032 | 40 - 320 Ncm | 40 Ncm | MECH TORQUE GAUGE |
UT CM 20L00050 | 50 - 500 Ncm | 50 Ncm | MECH TORQUE GAUGE |
UT CM 10K00050 | 0.04 - 0.5 Ncm | 0.04 Ncm | MECH TORQUE GAUGE |
UT CM 10K00150 | 0.1 - 1.5 Ncm | 0.1 Ncm | MECH TORQUE GAUGE |
UT CM 10K00600 | 0.4 - 6 Ncm | 0.4 Ncm | MECH TORQUE GAUGE |
UT CM 10K01200 | 0.8 - 12 Ncm | 0.8 Ncm | MECH TORQUE GA |
UTCM 20L00050机械扭力计机械扭力计这是一种基本的扭力计,适合于试验室或工厂种的多种低量程测量。它体积小,在测量调整旋钮或塑料张力有不可替代的作用。
技 术 参 数
1.可进顺逆时针扭力测试
2.峰值点自动记录
3.操作简单,价格低廉
4.精度:2%
5.提供标准金属仪表箱
机型 | 量程(Force) | 分辨率(Force) | 产品说明 |
UT CM 20L00002 | 2 - 20 Ncm | 2 Ncm | MECH TORQUE GAUGE |
UT CM 20L00004 | 5 - 40 Ncm | 5 Ncm | MECH TORQUE GAUGE |
UT CM 20L00008 | 10 - 80 Ncm | 10 Ncm | MECH TORQUE GAUGE |
UT CM 20L00016 | 20 - 160 Ncm | 20 Ncm | MECH TORQUE GAUGE |
UT CM 20L00032 | 40 - 320 Ncm | 40 Ncm | MECH TORQUE GAUGE |
UT CM 20L00050 | 50 - 500 Ncm | 50 Ncm | MECH TORQUE GAUGE |
UT CM 10K00050 | 0.04 - 0.5 Ncm | 0.04 Ncm | MECH TORQUE GAUGE |
UT CM 10K00150 | 0.1 - 1.5 Ncm | 0.1 Ncm | MECH TORQUE GAUGE |
UT CM 10K00600 | 0.4 - 6 Ncm | 0.4 Ncm | MECH TORQUE GAUGE |
UT CM 10K01200 | 0.8 - 12 Ncm | 0.8 Ncm | MECH TORQUE GAUGE |
NK表盘式测力表表盘式测力表价格低廉,但坚固可靠,用于测量压力和拉力。广泛用于机械和电子行业。
技术特点
1.可旋转表盘校零
2.峰值点自动记录
3.测量杆行程可达10mm
4.操作简单,价格低廉
5.精度:±1%
6.重量轻,仅重700克
7.提供标准仪表箱(备有:挂钩、测试盘、V型测头、锥形测头等)
Star带TM传感器数显扭力计技术参数:
◆ 顺、逆时针测试
◆ 精度:0.5%
◆ 分辨率:1/10000FS
◆ 双向峰值保持
◆ 当前值和峰值同时显示
◆ 扭矩/时间曲线图
◆ 显示曲线图上的特殊点:zui大值、任一时间值、拐点、导数值、*峰值、开始和结束值、平均值等
◆ 上一曲线图的保存
◆ 进度条显示
◆ 三个单位:Nm,Kg.cm,cm,mNm
◆ 取样频率:1000赫兹
◆ 可以用脚踏开关
◆ 校准功能
◆ 5~15分钟自动关机(可调)
◆ 可编程设置功能
◆ 双口RS232输出:随意传输zui大、zui小或当前值
◆ 数字量输出
◆ 曲线图输出
◆ 每秒50个值的传输速度
◆ 当前值的设定保护功能
◆ 自动确认传感器
◆ 可翻转显示功能
◆ 连续工作8小时不用充电
◆ 快速充电
◆ 可逆测量
◆ 背景光显示
◆ 可充电电池
◆ 低电提示
◆ 配置记忆功能
◆ 金属外壳并且内部有弹性保护膜
◆ 背后有用于固定在支架上的螺孔
◆ 校准证书
◆ 装有适配器和附件的便携工具箱
型号 | 量程 | 分辨率 |
CNR ST TM-04 | 0.4Nm | 0.04mNm |
CNR ST TM-07 | 0.7Nm | 0.07mNm |
6CNPK张力计名称
规格
包装
3CNP K张力计
测量范围:0.3至3 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
6CNP K张力计
测量范围:0.6至6 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
15CNP KM张力计
测量范围:2至15 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
30CNP KM张力计
测量范围:3至30 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
50CNP KM张力计
测量范围:5至50 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
100CNP KM张力计
测量范围:10至100 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
150CNP KM张力计
测量范围:10至150 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
250CNP KM张力计
测量范围:25至250 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
500CNP KM张力计
测量范围:50至500 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
1000CNP KM张力计
测量范围:100至1000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
2000CNP KM张力计
测量范围:200至2000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
1000CNPKM张力计
名称 | 规格 | 包装 |
3CNP K张力计 | 测量范围:0.3至3 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
6CNP K张力计 | 测量范围:0.6至6 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
15CNP KM张力计 | 测量范围:2至15 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
30CNP KM张力计 | 测量范围:3至30 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
50CNP KM张力计 | 测量范围:5至50 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
100CNP KM张力计 | 测量范围:10至100 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
150CNP KM张力计 | 测量范围:10至150 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
250CNP KM张力计 | 测量范围:25至250 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
500CNP KM张力计 | 测量范围:50至500 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
1000CNP KM张力计 | 测量范围:100至1000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
2000CNP KM张力计 | 测量范围:200至2000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
6CNPK张力计
名称 | 规格 | 包装 |
3CNP K张力计 | 测量范围:0.3至3 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
6CNP K张力计 | 测量范围:0.6至6 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
15CNP KM张力计 | 测量范围:2至15 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
30CNP KM张力计 | 测量范围:3至30 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
50CNP KM张力计 | 测量范围:5至50 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
100CNP KM张力计 | 测量范围:10至100 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
150CNP KM张力计 | 测量范围:10至150 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
250CNP KM张力计 | 测量范围:25至250 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
500CNP KM张力计 | 测量范围:50至500 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
1000CNP KM张力计 | 测量范围:100至1000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
2000CNP KM张力计 | 测量范围:200至2000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
100CNPKM张力计
名称 | 规格 | 包装 |
3CNP K张力计 | 测量范围:0.3至3 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
6CNP K张力计 | 测量范围:0.6至6 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
15CNP KM张力计 | 测量范围:2至15 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
30CNP KM张力计 | 测量范围:3至30 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
50CNP KM张力计 | 测量范围:5至50 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
100CNP KM张力计 | 测量范围:10至100 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
150CNP KM张力计 | 测量范围:10至150 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
250CNP KM张力计 | 测量范围:25至250 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
500CNP KM张力计 | 测量范围:50至500 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
1000CNP KM张力计 | 测量范围:100至1000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
2000CNP KM张力计 | 测量范围:200至2000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
500CNPKM张力计
名称 | 规格 | 包装 |
3CNP K张力计 | 测量范围:0.3至3 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
6CNP K张力计 | 测量范围:0.6至6 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
15CNP KM张力计 | 测量范围:2至15 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
30CNP KM张力计 | 测量范围:3至30 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
50CNP KM张力计 | 测量范围:5至50 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
100CNP KM张力计 | 测量范围:10至100 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
150CNP KM张力计 | 测量范围:10至150 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
250CNP KM张力计 | 测量范围:25至250 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
500CNP KM张力计 | 测量范围:50至500 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
1000CNP KM张力计 | 测量范围:100至1000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
2000CNP KM张力计 | 测量范围:200至2000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
50CNPKM张力计名称
规格
包装
3CNP K张力计
测量范围:0.3至3 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
6CNP K张力计
测量范围:0.6至6 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
15CNP KM张力计
测量范围:2至15 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
30CNP KM张力计
测量范围:3至30 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
50CNP KM张力计
测量范围:5至50 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
100CNP KM张力计
测量范围:10至100 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
150CNP KM张力计
测量范围:10至150 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
250CNP KM张力计
测量范围:25至250 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
500CNP KM张力计
测量范围:50至500 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
1000CNP KM张力计
测量范围:100至1000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
2000CNP KM张力计
测量范围:200至2000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
U型测力计30354-0058
Flat or recessed bottom gage
Maximum pointer
Shockless dial indicator
Dial orientation
0°, 900°, 1800°, 2700°
| ||||||||||||||||||||||||||||||||||
|
U型测力计30354-0066 Flat or recessed bottom gage
Maximum pointer
Shockless dial indicator
Dial orientation
0°, 900°, 1800°, 2700°
| ||||||||||||||||||||||||||||||||||
|
XC机械测力计30386-0035 Maximum Pointer Option
Shockless Dial Indicator
|
Maximum Pointer Option Shockless Dial Indicator |
| ||||||||||||||||||||||||||||||||||||||||||||||||||||
|
30799-0010XPP机械测力计XPP - Tension/Compression - Mechanical Force Gage
Maximum Pointer (Not Available)
Shockless Dial Indicator
| ||||||||||||||||||||||||||||||||||||||||||||||||||||
|
30800-0017XPP机械测力计
| ||||||||||||||||||||||||||||||||||||||||||||||||||||
|
RON2501-80T吊秤
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
RON2501-125T吊秤
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
BlueForce冲击测力计lueForce: one of a kind, with dual Bluetooth and USB interface
Thanks to the PC-LINK mode, Blue Force can also be linked up to a handheld computer or a PC during testing, allowing immediate viewing of the graph and values, as a well as immediate access to test results.
The comfortable handle, in an accessible and ergonomic position, ensures a steady grip and matchless manoeuvrability; the handle is also easy to remove (using the key supplied) and can be rotated by 180° (i.e. turned upside down). CENTOR STAR
曲线显示测力计技 术 参 数
1.可测拉力和压力 | 2.可充电电池 |
3.精度:0.25%(满量程) | 4.低电量提示 |
5.分辨率: 0.1N 配置记忆功能 | 6.拉力和压力的峰值锁定功能 |
7.连续工作8小时不用充电 | 8.三种单位:牛顿、公斤力、磅 |
9.金属外壳并且内部有弹性保护膜 | 10.取样频率:1000赫兹 |
11.背后有用于固定在支架上的螺孔 | 12.自校准功能 |
13.校准证书 | 14.15分钟自动关机 |
15.装有适配器和附件的便携工具箱 | 16.可显示功能 |
17.200%的过载保护 |
型号 | 量程 | 分辨率 | 产品说明 |
CNR SP | - | - | CENTOR EASY DISPLAY |
CNR SP 5 | 5 N | 0.0005 N | FORCE GAUGE CENTOR EASY 5N |
CNR SP 10 | 10 N | 0.001 N | FORCE GAUGE CENTOR EASY 10N |
CNR SP 25 | 25 N | 0.002 N | FORCE GAUGE CENTOR EASY 25N |
CNR SP 50 | 50 N | 0.005 N | FORCE GAUGE CENTOR EASY 50N |
CNR SP 100 | 100 N | 0.01 N | FORCE GAUGE CENTOR EASY 100N |
CNR SP 250 | 250 N | 0.02 N | FORCE GAUGE CENTOR EASY 250N |
CNR SP 500 | 500 N | 0.05 N | FORCE GAUGE CENTOR EASY 500N |
CNR SP 1KN | 1000 N | 0.1 N | FORCE GAUGE CENTOR EASY 1000N |
2数显推拉力计
模式 | 标准型 | FGC-0.2 | FGC-0.5 | FGC-1 | FGC-2 | FGC-5 |
经济型 | — | — | — | FGN-2 | FGN-5 | |
定额负荷量 | ±1.961N | ±4.903N | ±9.81N | ±19.61N | ±49.03N | |
±200.0gf | ±500.0gf | ±1000gf | ±2.000kgf | ±5.000kgf | ||
±8.00ozf | ±16.00ozf | ±2.000lbf | ±5.000lbf | ±10.00lbf | ||
测量范围 | ±2.00N | ±5.000N | ±10.00N | ±20.00N | ±50.00N | |
±200.0gf | ±500.0gf | ±1000gf | ±2.000kgf | ±5.000kgf | ||
±8.00ozf | ±16.00ozf | ±2.00lbf | ±5.00lbf | ±10.00lbf | ||
分辨率 | 0.001N/0.1gf/0.01ozf | 0.01N/1gf/0.001lbf | 0.1N/0.001kgf/0.01lbf | |||
测量单位 | (易于转换显示功能单位) | |||||
测量方法 | 正常测定和峰值测定 | |||||
更新时间 | 0.3秒 | |||||
测量次数 | 35次/秒 | |||||
精度 | ±0.2%R.C.+1/2位(23C) | |||||
温度效应 | 变化范围:零点偏移/因牵引而消除 | |||||
显示 | 4位12mm高LCD,1个张力显示用(可选转换显示)其他显示器:1.“LOWBAT" 2.“BAT"(电池正充电)3.“OVR"(超载)4.“PEAK"(峰值模式) | |||||
超载容许 | R.C. 200% | |||||
Teacking功能 | 开/关可供选择 | |||||
输出信号 | RS-232C | 有(通过通信软件,可以与PC连接.与PC的连接线为另卖品)连续送信zui大为100次/秒 | ||||
模拟 | ±1V(±zui大值载入)12位D/A转换方法,输出间隔140次/秒 | |||||
超载 | 开放式连接器输出(DC30V 5mA zui大值) | |||||
电源 | 镍镉电池和AC适配器(DC9V 200mA) | |||||
电源自动关闭功能 | 待机10分钟,由AC供电时能够连续使用 | |||||
操作温度 | 0~40℃ | |||||
尺寸 | 宽75*高38*长147mm | |||||
重量 | 约450g | |||||
附件(包括在内) | 扁平顶盖,挂钩,钢凿,三角带,椎体,扩展杆,便携式提箱,直流电源适配器,RS-232C线 |
FGC-100HB测力仪模式
标准型
FGC-0.2
FGC-0.5
FGC-1B
FGC-2B
FGC-5B
经济型
—
—
—
FGN-2B
FGN-5B
定额负荷量
±1.961N
±4.903N
±9.81N
±19.61N
±49.03N
±200.0gf
±500.0gf
±1000gf
±2.000kgf
±5.000kgf
±8.00ozf
±16.00ozf
±2.000lbf
±5.000lbf
±10.00lbf
测量范围
±2.00N
±5.000N
±10.00N
±20.00N
±50.00N
±200.0gf
±500.0gf
±1000gf
±2.000kgf
±5.000kgf
±8.00ozf
±16.00ozf
±2.00lbf
±5.00lbf
±10.00lbf
分辨率
0.001N/0.1gf/0.01ozf
0.01N/1gf/0.001lbf
0.1N/0.001kgf/0.01lbf
测量单位
(易于转换显示功能单位)
测量方法
正常测定和峰值测定
更新时间
0.3秒
测量次数
35次/秒
精度
±0.2%R.C.+1/2位(23C)
温度效应
变化范围:零点偏移/因牵引而消除
显示
4位12mm高LCD,1个张力显示用(可选转换显示)其他显示器:1.“LOWBAT" 2.“BAT"(电池正充电)3.“OVR"(超载)4.“PEAK"(峰值模式)
超载容许
R.C. 200%
Teacking功能
开/关可供选择
输出信号
RS-232C
有(通过通信软件,可以与PC连接.与PC的连接线为另卖品)连续送信zui大为100次/秒
模拟
±1V(±zui大值载入)12位D/A转换方法,输出间隔140次/秒
超载
开放式连接器输出(DC30V 5mA zui大值)
电源
镍镉电池和AC适配器(DC9V 200mA)
电源自动关闭功能
待机10分钟,由AC供电时能够连续使用
操作温度
0~40℃
尺寸
宽75*高38*长147mm
重量
约450g
附件(包括在内)
扁平顶盖,挂钩,钢凿,三角带,椎体,扩展杆,便携式提箱,直流电源适配器,RS-232C线
55075010数显扭矩扳手
左右手适用,精细棘轮头。Nm,ft.ib和In.Ib三刻度显示,LED指示灯指示功能。两种工作模式。 电脑及打印机连口。+/-2%高精确度,有独立的检验证书和序列号。
ACX-500数字航天电缆张力计
ACX-100数字航空用钢丝绳张力计
STANDARD INSTRUMENTS: |
Model | Range | Resolution | Standard Cable Selections |
ACX-100 | 5-100 lbs | 0.5 lb | 1/16", 3/32", 1/8", 5/32" |
ACX-250 | 20-250 lbs | 0.5 lb | 1/16", 3/32", 1/8", 5/32" |
ACX-500 | 40-500 lbs | 1 lb | 3/32", 1/8", 5/32" |
ACX-CWT | 20-250 lbs | 0.5 lb | CWT-5,CWT-10,CWT-15,CWT-20,CWT-25 |
ACX-CMB | 20-250 lbs | 0.5 lb | 1/16",3/32",1/8",5/32", CWT-5 thru CWT-25 |
*Calibrations for 3/16", 7/32" and for metric sized cables can be added to the cable selection menu upon request, however cables with diameters larger than 5/32" will only indicate up to approximay 90% of maximum tension range. For example, an instrument scaled for a maximum tension range of 250 lbs will display readings up to approximay 225 lbs on 7/32" or 3/16" diameter cables.
· Available Options for all Instruments |
Option designator -A | Analog Output Option |
Option designator -E | RS-232 Serial Output Option |
Option designator -D | Data Logging Option Option |
Note: Add option-designator letter to the end of the Model Number. (For example, a Model ACX-250-E denotes a standard ACX-250 with the optional RS-232, serial output function included.)
· Instruments can be configured with any or all of these options.
ACX-100数字航空用钢丝绳张力计
STANDARD INSTRUMENTS: |
Model | Range | Resolution | Standard Cable Selections |
ACX-100 | 5-100 lbs | 0.5 lb | 1/16", 3/32", 1/8", 5/32" |
ACX-250 | 20-250 lbs | 0.5 lb | 1/16", 3/32", 1/8", 5/32" |
ACX-500 | 40-500 lbs | 1 lb | 3/32", 1/8", 5/32" |
ACX-CWT | 20-250 lbs | 0.5 lb | CWT-5,CWT-10,CWT-15,CWT-20,CWT-25 |
ACX-CMB | 20-250 lbs | 0.5 lb | 1/16",3/32",1/8",5/32", CWT-5 thru CWT-25 |
*Calibrations for 3/16", 7/32" and for metric sized cables can be added to the cable selection menu upon request, however cables with diameters larger than 5/32" will only indicate up to approximay 90% of maximum tension range. For example, an instrument scaled for a maximum tension range of 250 lbs will display readings up to approximay 225 lbs on 7/32" or 3/16" diameter cables.
· Available Options for all Instruments |
Option designator -A | Analog Output Option |
Option designator -E | RS-232 Serial Output Option |
Option designator -D | Data Logging Option Option |
Note: Add option-designator letter to the end of the Model Number. (For example, a Model ACX-250-E denotes a standard ACX-250 with the optional RS-232, serial output function included.)
· Instruments can be configured with any or all of these options.
STX-2000张力计
STANDARD INSTRUMENTS: STX-Series Models are calibrated specifically to your strapping types(s) and size(s) to ensure greatest accuracy. |
Model | Range | Resolution | Full-Scale Accuracy |
STX-2000 | 100-2000 lbs | 10 lb | 2% |
STXM INSTRUMENTS: STXM instruments include multiple calibrations for different Poly and PET strapping sizes. |
Model | Range | Resolution | Full-Scale Accuracy |
STXM-2000* | 100-2000 lbs | 10 lb | 4% |
STX-1000张力计
STANDARD INSTRUMENTS: STX-Series Models are calibrated specifically to your strapping types(s) and size(s) to ensure greatest accuracy. |
Model | Range | Resolution | Full-Scale Accuracy |
STX-1000 | 50-1000 lbs | 5 lb | 1% |
STXM INSTRUMENTS: STXM instruments include multiple calibrations for different Poly and PET strapping sizes. |
Model | Range | Resolution | Full-Scale Accuracy |
STXM-1000 | 50-1000 lbs | 5 lb | 4% |
*The STXM-2000 includes all calibrations for POLY and PET strapping with thicknesses from .020" - .055", and STEEL strapping with thicknesses between .017" - .044".
· Data Logging has adjustable duration and sampling rates.
· Large, easy to read backlit, graphic display with adjustable backlighting and contrast.
· Select tension values to display in lbs, Kg, or Newtons.
· Select strap material and size from menu. Instrument automatically adjusts calibration for your specific setting.
· Up to 10 calibrations can be programmed into instrument. (All calibrations password protected.)
· Adjustable LCD refresh rates allow for stable digital readings.
· All models typically available from stock.
· All models factory-calibrated and ready for use.
· Calibration values traceable to National Standards. Calibration certificate included.
Available Options for all Instruments |
· Note: Add option-designator letter to the end of the Model Number. (For example, a Model STX-1000-A denotes a standard STX-1000 with the optional Analog Output function included.)
A | Analog Output Option |
E | RS-232 Serial Output Option |
D | Data Logging Option |
ACM-600张力计
CX-2000张力计
CX-2000张力计
TR-25机械张力计
Model "TR" Series |
Range In Grams | Use Model Number |
25 g | TR-25 |
125 g | TR-125 |
250 g | TR-250 |
1000 g | TR-1000 |
2000 g | TR-2000 |
4000 g | TR-4000 |
5000 g | TR-5000 |
WC系列张力计
The Sheet Tension Meter, Model WC-series, measures the tension of any width material which is long, flat and thin, such as: paper, film, plastic sheets, cloth, web, loom beams, metal foils or winding electrical condensers.
The Sheet Tension Meter, Model WC-series measures tension in flexible sheets or webs which are typically 8" or wider. The instrument is inserted from the edge and measures per inch of web width up to 4" inside your material, so the waviness at the edges is avoided. Hand crafted from solid anodized aluminum, ranges are available to measure tension up to 100 pli or 50 kg/pli.
Ensure consistency in your manufacturing process.
Direct Reading or Comparator Dials Available.
Adaptable for materials as thin as paper to sheets as stiff as foils.
Engagement and disengagement onto materials is quick, safe and easy.
Readings are obtained regardless of meter position.
Weighs only 3 lb. LX-250张力计
For use on materials with critical tension ranges up to 500 lbs.
Large, easy to read, graphic display with adjustable backlighting and contrast.
Select tension values to indicate in Lbs, Kg or Newtons.
Display shows Tension, Battery Charge level and Material selected.
Push a button to activate the Memory Function to store and display up to five separate tension readings plus the average value (AVG) of these stored readings.
Accuracy is +/- 2% full-scale for all menu-selectable calibrations. Accuracy for custom calibrations is material specific. • Up to 10 calibrations can be programmed into instrument. (All calibrations are password protected to provide due diligence against unauthorized changes).
Adjustable LCD refresh rates allow for stable digital readings.
All models typically available from stock.
All models factory calibrated and ready for use.
All calibration values traceable to National Standards.
Calibration certificate included.
MODEL | RANGE | RESOLUTION |
LX-250 | 5-250 LB Grooved Pulleys | 0.5 LB |
AVAILABLE OPTIONS FOR ALL INSTRUMENTS
Note: Add option designator to the end of the part number. (i.e.: a Model LX-250-E denotes a standard, LX-250 with the optional RS-232, serial output function installed).
-A Analog Output option. 0-5 VDC or 4-20mA with Software-definable ending sequences. Provided with 10’ of cable. Data outputted at 40 Hz.
-E RS-233 Serial Output option. Provided with 10’ cable to Interface with your receiving device. Select data sampling rate from 1, 2 or 5 Hz.
Input Real-Time Serial Data into any Windows® application using the optional software WinWedge Pro® for Windows, or configure your Window’s® operating system to capture the data via Hyper Terminal®.
SPECIFICATIONS:
Approximate weight is 1-1/2 lb (Weight varies depending upon instrument configuration).
Re-chargeable NIMH battery with power supply provided. Recommended temperature range for instruments is 35 - 115° F. Approximay 6 hours of operation per battery charge depending upon backlighting intensity.
Power Supply operates with input voltages from 100 – 240V and includes several, interchangeable “blades" allowing use with European, US, Australian and other plug configurations.
Automatic shutoff after 10 minutes of non-use.
Instruments may be operated continuously while connected to power supply.
Durable, lightweight carrying case with protective foam inserts.
CE Certification complying with heavy, industrial immunity standards.
BTM系列张力计pical Weight: 2 lb, 14 oz
Easy To Read Dial in lg or kg
Right- or Left-Hand Operation
Durable Solid Anodized Aluminum Construction
Sturdy Handle For Ease of Use on Moving Materials
Provided with Heavy Duty Polyethylene Carrying Case
Stainless Steel, Anodized Aluminum, P.T.F.E. or Delrin Contact Elements Available
The Band Tension Meter is used to measure the tension in tapes or many wires/yarns in parallel. Ranges are available up to 500 lb or 250 kg. This instrument is ideal for use with bands, flat cable, and flat conductors as well as round wire/cable configurations. The contact rollers can be made up to 3" long, plus the instrument can be outfitted with a variety of small grooved pulleys for round wire and cable applications. Please Tensitron if you would like assistance in selecting the appropriate meter for your specific application.
LXR-500张力计For use on materials with critical tension ranges up to 500 lbs.
Large, easy to read, graphic display with adjustable backlighting and contrast.
Select tension values to indicate in Lbs, Kg or Newtons.
Display shows Tension, Battery Charge level and Material selected.
Push a button to activate the Memory Function to store and display up to five separate tension readings plus the average value (AVG) of these stored readings.
Accuracy is +/- 2% full-scale for all menu-selectable calibrations. Accuracy for custom calibrations is material specific. • Up to 10 calibrations can be programmed into instrument. (All calibrations are password protected to provide due diligence against unauthorized changes).
Adjustable LCD refresh rates allow for stable digital readings.
All models typically available from stock.
All models factory calibrated and ready for use.
All calibration values traceable to National Standards.
Calibration certificate included.
MODEL | RANGE | RESOLUTION |
LXR-500 | 25-500 LB 1" Tape Roller | 1 LB |
AVAILABLE OPTIONS FOR ALL INSTRUMENTS
Note: Add option designator to the end of the part number. (i.e.: a Model LX-250-E denotes a standard, LX-250 with the optional RS-232, serial output function installed).
-A Analog Output option. 0-5 VDC or 4-20mA with Software-definable ending sequences. Provided with 10’ of cable. Data outputted at 40 Hz.
-E RS-233 Serial Output option. Provided with 10’ cable to Interface with your receiving device. Select data sampling rate from 1, 2 or 5 Hz.
Input Real-Time Serial Data into any Windows® application using the optional software WinWedge Pro® for Windows, or configure your Window’s® operating system to capture the data via Hyper Terminal®.
SPECIFICATIONS:
Approximate weight is 1-1/2 lb (Weight varies depending upon instrument configuration).
Re-chargeable NIMH battery with power supply provided. Recommended temperature range for instruments is 35 - 115° F. Approximay 6 hours of operation per battery charge depending upon backlighting intensity.
Power Supply operates with input voltages from 100 – 240V and includes several, interchangeable “blades" allowing use with European, US, Australian and other plug configurations.
Automatic shutoff after 10 minutes of non-use.
Instruments may be operated continuously while connected to power supply.
Durable, lightweight carrying case with protective foam inserts.
CE Certification complying with heavy, industrial immunity standards.
ATLAS系列高载荷测试机ATLAS系列高载荷测试机ATLAS5到50KN测试机用于测试力大于5KN的试验中。强力发动机和双柱结构的结合使该机与STENTORS有相似的功能。基座有一个适于安装夹具的固定孔。传感器固定于横梁上,横梁由双螺杆系统移动,并由双立柱导轨控制升降。ATLAS系列的控制台和STENOR采用相同的控制系统。
ANDILOG传感器
型号 | 精度 | 量程 | 分辨率 |
SPIP TM 0.4 | 0.5%FS | 0.4Nm | 0.05mNm |
SPIP TM 0.7 | 0.5%FS | 0.7Nm | 0.07mNm |
型号 | 精度 | 量程 | 分辨率 |
SPIP TH 0.12 | 0.5%FS | 0.12Nm | 0.01mNm |
SPIP TH 0.3 | 0.5%FS | 0.3Nm | 0.03mNm |
SPIP TH 1.5 | 0.5%FS | 1.5Nm | 0.1mNm |
SPIP TH 0 | 0.5%FS | 6Nm | 0.6mNm |
SPIP TH 12 | 0.5%FS | 12Nm | 1mNm |
型号 | 精度 | 量程 | 分辨率 |
SPIP TT 0.05 | 0.5%FS | 0.05Nm | 0.005mNm |
SPIP TT 0.15 | 0.5%FS | 0.15Nm | 0.02mNm |
SPIP TT 0.35 | 0.5%FS | 0.35Nm | 0.03mNm |
SPIP TT 0.75 | 0.5%FS | 0.75Nm | 0.1mNm |
SPIP TT 1 | 0.5%FS | 1Nm | 0.1mNm |
SPIP TT 3 | 0.5%FS | 3Nm | 0.3mNm |
SPIP TT 6 | 0.5%FS | 6Nm | 0.6mNm |
SPIP TT 12 | 0.5%FS | 12Nm | 1mNm |
SPIP TT 24 | 0.5%FS | 24Nm | 2mNm |
SPIP TT 60 | 0.5%FS | 60Nm | 5mNm |
型号 | 精度 | 量程 | 分辨率 |
SPIP TW 15 | 0.5%FS | 15Nm | 1mNm |
SPIP TW 60 | 0.5%FS | 60Nm | 6mNm |
SPIP TW 150 | 0.5%FS | 150Nm | 0.02mNm |
SPIP TW 600 | 0.5%FS | 600Nm | 0.06mNm |
EASY带TM传感器数显扭力计同样使用了CENTOR技术。CENTOR W EASY数显扭力计采用一个超大的显示屏可以显示精确测量结果。它可以同时显示当前值、峰值。进度条显示了测量是否接近zui大量程。如有需要背景光可以让读数更加容易。
它*的测量设备可以使取样频率在1000赫兹,分辨率在1/10000FS,误差小于0.5%(满量程)。
同时还可拓展其它多种功能来完善该仪器。
设点功能可以设置“合格,不合格",同时信号会在显示屏上表示出来,通过RS232输出端可以连接电脑。
数字输出可以用Mitutoyo打印机进行数据打印。
技术参数
·顺、逆时针双向转动
·精度:0.5%(满量程)
·分辨率:1/1000FS
·峰值锁定功能(双向)
·当前值和峰值同时显示
·进度条显示功能
·三种单位:牛米、千克厘米、毫牛米
·取样频率:1000赫兹
·可以用脚踏开关
·校准功能
·.5-15分钟自动关机(可调)-
·可编程设置功能
·.双口RS232输出:随意传输zui大、zui小或当前值
·数字输出
·连续工作8小时不用充电
·快速充电
·翻转显示功能
·背景光显示
·可充电电池
·低电提示
·配置记忆功能
·金属外壳并且内部有弹性保护膜
·背后有用于固定在支架上的螺孔
·校准证书
·.装有适配器和附件的便携工具箱
型号 | 量程 | 分辨率 |
CNR EA TM-04 | 0.4Nm | 0.04mNm |
CNR EA TM-07 | 0.7Nm | 0.07mNm |
Star带TW传感器数显扭力计技术参数:
◆ 顺、逆时针测试
◆ 精度:0.5%
◆ 分辨率:1/10000FS
◆ 双向峰值保持
◆ 当前值和峰值同时显示
◆ 扭矩/时间曲线图
◆ 显示曲线图上的特殊点:zui大值、任一时间值、拐点、导数值、*峰值、开始和结束值、平均值等
◆ 上一曲线图的保存
◆ 进度条显示
◆ 三个单位:Nm,Kg.cm,cm,mNm
◆ 取样频率:1000赫兹
◆ 可以用脚踏开关
◆ 校准功能
◆ 5~15分钟自动关机(可调)
◆ 可编程设置功能
◆ 双口RS232输出:随意传输zui大、zui小或当前值
◆ 数字量输出
◆ 曲线图输出
◆ 每秒50个值的传输速度
◆ 当前值的设定保护功能
◆ 自动确认传感器
◆ 可翻转显示功能
◆ 连续工作8小时不用充电
◆ 快速充电
◆ 可逆测量
◆ 背景光显示
◆ 可充电电池
◆ 低电提示
◆ 配置记忆功能
◆ 金属外壳并且内部有弹性保护膜
◆ 背后有用于固定在支架上的螺孔
◆ 校准证书
◆ 装有适配器和附件的便携工具箱
型号 | 量程 | 分辨率 |
CNR ST TW-15 | 15Nm | 1.5mNm |
CNR ST TW-60 | 60Nm | 6mNm |
CNR ST TW-150 | 150Nm | 0.015mNm |
CNR ST TW-600 | 600Nm | 0.06mNm |
UTCM 20L00050机械扭力计5.提供标准金属仪表箱
机型 | 量程(Force) | 分辨率(Force) | 产品说明 |
UT CM 20L00002 | 2 - 20 Ncm | 2 Ncm | MECH TORQUE GAUGE |
UT CM 20L00004 | 5 - 40 Ncm | 5 Ncm | MECH TORQUE GAUGE |
UT CM 20L00008 | 10 - 80 Ncm | 10 Ncm | MECH TORQUE GAUGE |
UT CM 20L00016 | 20 - 160 Ncm | 20 Ncm | MECH TORQUE GAUGE |
UT CM 20L00032 | 40 - 320 Ncm | 40 Ncm | MECH TORQUE GAUGE |
UT CM 20L00050 | 50 - 500 Ncm | 50 Ncm | MECH TORQUE GAUGE |
UT CM 10K00050 | 0.04 - 0.5 Ncm | 0.04 Ncm | MECH TORQUE GAUGE |
UT CM 10K00150 | 0.1 - 1.5 Ncm | 0.1 Ncm | MECH TORQUE GAUGE |
UT CM 10K00600 | 0.4 - 6 Ncm | 0.4 Ncm | MECH TORQUE GAUGE |
UT CM 10K01200 | 0.8 - 12 Ncm | 0.8 Ncm | MECH TORQUE GA |
UTCM 20L00050机械扭力计机械扭力计这是一种基本的扭力计,适合于试验室或工厂种的多种低量程测量。它体积小,在测量调整旋钮或塑料张力有不可替代的作用。
技 术 参 数
1.可进顺逆时针扭力测试
2.峰值点自动记录
3.操作简单,价格低廉
4.精度:2%
5.提供标准金属仪表箱
机型 | 量程(Force) | 分辨率(Force) | 产品说明 |
UT CM 20L00002 | 2 - 20 Ncm | 2 Ncm | MECH TORQUE GAUGE |
UT CM 20L00004 | 5 - 40 Ncm | 5 Ncm | MECH TORQUE GAUGE |
UT CM 20L00008 | 10 - 80 Ncm | 10 Ncm | MECH TORQUE GAUGE |
UT CM 20L00016 | 20 - 160 Ncm | 20 Ncm | MECH TORQUE GAUGE |
UT CM 20L00032 | 40 - 320 Ncm | 40 Ncm | MECH TORQUE GAUGE |
UT CM 20L00050 | 50 - 500 Ncm | 50 Ncm | MECH TORQUE GAUGE |
UT CM 10K00050 | 0.04 - 0.5 Ncm | 0.04 Ncm | MECH TORQUE GAUGE |
UT CM 10K00150 | 0.1 - 1.5 Ncm | 0.1 Ncm | MECH TORQUE GAUGE |
UT CM 10K00600 | 0.4 - 6 Ncm | 0.4 Ncm | MECH TORQUE GAUGE |
UT CM 10K01200 | 0.8 - 12 Ncm | 0.8 Ncm | MECH TORQUE GAUGE |
NK表盘式测力表表盘式测力表价格低廉,但坚固可靠,用于测量压力和拉力。广泛用于机械和电子行业。
技术特点
1.可旋转表盘校零
2.峰值点自动记录
3.测量杆行程可达10mm
4.操作简单,价格低廉
5.精度:±1%
6.重量轻,仅重700克
7.提供标准仪表箱(备有:挂钩、测试盘、V型测头、锥形测头等)
Star带TM传感器数显扭力计技术参数:
◆ 顺、逆时针测试
◆ 精度:0.5%
◆ 分辨率:1/10000FS
◆ 双向峰值保持
◆ 当前值和峰值同时显示
◆ 扭矩/时间曲线图
◆ 显示曲线图上的特殊点:zui大值、任一时间值、拐点、导数值、*峰值、开始和结束值、平均值等
◆ 上一曲线图的保存
◆ 进度条显示
◆ 三个单位:Nm,Kg.cm,cm,mNm
◆ 取样频率:1000赫兹
◆ 可以用脚踏开关
◆ 校准功能
◆ 5~15分钟自动关机(可调)
◆ 可编程设置功能
◆ 双口RS232输出:随意传输zui大、zui小或当前值
◆ 数字量输出
◆ 曲线图输出
◆ 每秒50个值的传输速度
◆ 当前值的设定保护功能
◆ 自动确认传感器
◆ 可翻转显示功能
◆ 连续工作8小时不用充电
◆ 快速充电
◆ 可逆测量
◆ 背景光显示
◆ 可充电电池
◆ 低电提示
◆ 配置记忆功能
◆ 金属外壳并且内部有弹性保护膜
◆ 背后有用于固定在支架上的螺孔
◆ 校准证书
◆ 装有适配器和附件的便携工具箱
型号 | 量程 | 分辨率 |
CNR ST TM-04 | 0.4Nm | 0.04mNm |
CNR ST TM-07 | 0.7Nm | 0.07mNm |
6CNPK张力计名称
规格
包装
3CNP K张力计
测量范围:0.3至3 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
6CNP K张力计
测量范围:0.6至6 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
15CNP KM张力计
测量范围:2至15 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
30CNP KM张力计
测量范围:3至30 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
50CNP KM张力计
测量范围:5至50 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
100CNP KM张力计
测量范围:10至100 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
150CNP KM张力计
测量范围:10至150 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
250CNP KM张力计
测量范围:25至250 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
500CNP KM张力计
测量范围:50至500 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
1000CNP KM张力计
测量范围:100至1000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
2000CNP KM张力计
测量范围:200至2000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
1000CNPKM张力计
名称 | 规格 | 包装 |
3CNP K张力计 | 测量范围:0.3至3 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
6CNP K张力计 | 测量范围:0.6至6 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
15CNP KM张力计 | 测量范围:2至15 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
30CNP KM张力计 | 测量范围:3至30 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
50CNP KM张力计 | 测量范围:5至50 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
100CNP KM张力计 | 测量范围:10至100 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
150CNP KM张力计 | 测量范围:10至150 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
250CNP KM张力计 | 测量范围:25至250 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
500CNP KM张力计 | 测量范围:50至500 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
1000CNP KM张力计 | 测量范围:100至1000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
2000CNP KM张力计 | 测量范围:200至2000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
6CNPK张力计
名称 | 规格 | 包装 |
3CNP K张力计 | 测量范围:0.3至3 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
6CNP K张力计 | 测量范围:0.6至6 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
15CNP KM张力计 | 测量范围:2至15 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
30CNP KM张力计 | 测量范围:3至30 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
50CNP KM张力计 | 测量范围:5至50 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
100CNP KM张力计 | 测量范围:10至100 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
150CNP KM张力计 | 测量范围:10至150 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
250CNP KM张力计 | 测量范围:25至250 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
500CNP KM张力计 | 测量范围:50至500 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
1000CNP KM张力计 | 测量范围:100至1000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
2000CNP KM张力计 | 测量范围:200至2000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
100CNPKM张力计
名称 | 规格 | 包装 |
3CNP K张力计 | 测量范围:0.3至3 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
6CNP K张力计 | 测量范围:0.6至6 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
15CNP KM张力计 | 测量范围:2至15 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
30CNP KM张力计 | 测量范围:3至30 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
50CNP KM张力计 | 测量范围:5至50 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
100CNP KM张力计 | 测量范围:10至100 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
150CNP KM张力计 | 测量范围:10至150 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
250CNP KM张力计 | 测量范围:25至250 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
500CNP KM张力计 | 测量范围:50至500 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
1000CNP KM张力计 | 测量范围:100至1000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
2000CNP KM张力计 | 测量范围:200至2000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
500CNPKM张力计
名称 | 规格 | 包装 |
3CNP K张力计 | 测量范围:0.3至3 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
6CNP K张力计 | 测量范围:0.6至6 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
15CNP KM张力计 | 测量范围:2至15 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
30CNP KM张力计 | 测量范围:3至30 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
50CNP KM张力计 | 测量范围:5至50 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
100CNP KM张力计 | 测量范围:10至100 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
150CNP KM张力计 | 测量范围:10至150 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
250CNP KM张力计 | 测量范围:25至250 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
500CNP KM张力计 | 测量范围:50至500 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
1000CNP KM张力计 | 测量范围:100至1000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
2000CNP KM张力计 | 测量范围:200至2000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数) | 1支 |
50CNPKM张力计名称
规格
包装
3CNP K张力计
测量范围:0.3至3 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
6CNP K张力计
测量范围:0.6至6 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
15CNP KM张力计
测量范围:2至15 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
30CNP KM张力计
测量范围:3至30 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
50CNP KM张力计
测量范围:5至50 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
100CNP KM张力计
测量范围:10至100 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
150CNP KM张力计
测量范围:10至150 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
250CNP KM张力计
测量范围:25至250 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
500CNP KM张力计
测量范围:50至500 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
1000CNP KM张力计
测量范围:100至1000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
2000CNP KM张力计
测量范围:200至2000 精密度:+/-0.01×(刻度盘zui大读数+实际测得之读数)
1支
U型测力计30354-0058
Flat or recessed bottom gage
Maximum pointer
Shockless dial indicator
Dial orientation
0°, 900°, 1800°, 2700°
| ||||||||||||||||||||||||||||||||||
|
U型测力计30354-0066 Flat or recessed bottom gage
Maximum pointer
Shockless dial indicator
Dial orientation
0°, 900°, 1800°, 2700°
| ||||||||||||||||||||||||||||||||||
|
XC机械测力计30386-0035 Maximum Pointer Option
Shockless Dial Indicator
|
Maximum Pointer Option Shockless Dial Indicator |
| ||||||||||||||||||||||||||||||||||||||||||||||||||||
|
30799-0010XPP机械测力计XPP - Tension/Compression - Mechanical Force Gage
Maximum Pointer (Not Available)
Shockless Dial Indicator
| ||||||||||||||||||||||||||||||||||||||||||||||||||||
|
30800-0017XPP机械测力计
| ||||||||||||||||||||||||||||||||||||||||||||||||||||
|
RON2501-80T吊秤
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
RON2501-125T吊秤
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
BlueForce冲击测力计lueForce: one of a kind, with dual Bluetooth and USB interface
Thanks to the PC-LINK mode, Blue Force can also be linked up to a handheld computer or a PC during testing, allowing immediate viewing of the graph and values, as a well as immediate access to test results.
The comfortable handle, in an accessible and ergonomic position, ensures a steady grip and matchless manoeuvrability; the handle is also easy to remove (using the key supplied) and can be rotated by 180° (i.e. turned upside down). CENTOR STAR
曲线显示测力计技 术 参 数
1.可测拉力和压力 | 2.可充电电池 |
3.精度:0.25%(满量程) | 4.低电量提示 |
5.分辨率: 0.1N 配置记忆功能 | 6.拉力和压力的峰值锁定功能 |
7.连续工作8小时不用充电 | 8.三种单位:牛顿、公斤力、磅 |
9.金属外壳并且内部有弹性保护膜 | 10.取样频率:1000赫兹 |
11.背后有用于固定在支架上的螺孔 | 12.自校准功能 |
13.校准证书 | 14.15分钟自动关机 |
15.装有适配器和附件的便携工具箱 | 16.可显示功能 |
17.200%的过载保护 |
型号 | 量程 | 分辨率 | 产品说明 |
CNR SP | - | - | CENTOR EASY DISPLAY |
CNR SP 5 | 5 N | 0.0005 N | FORCE GAUGE CENTOR EASY 5N |
CNR SP 10 | 10 N | 0.001 N | FORCE GAUGE CENTOR EASY 10N |
CNR SP 25 | 25 N | 0.002 N | FORCE GAUGE CENTOR EASY 25N |
CNR SP 50 | 50 N | 0.005 N | FORCE GAUGE CENTOR EASY 50N |
CNR SP 100 | 100 N | 0.01 N | FORCE GAUGE CENTOR EASY 100N |
CNR SP 250 | 250 N | 0.02 N | FORCE GAUGE CENTOR EASY 250N |
CNR SP 500 | 500 N | 0.05 N | FORCE GAUGE CENTOR EASY 500N |
CNR SP 1KN | 1000 N | 0.1 N | FORCE GAUGE CENTOR EASY 1000N |
如果您对本品感兴趣请与我公司
北京恒远安诺科技有限公司
联 系 人:王志斌 ()
手 机:
: 2326210708
电子邮件: 2326210708
公司:http://www.annovatek.com/
地址: 北京市朝阳区大郊亭中街2号院华腾3座10A